Are you looking for a way to have some fun while bypassing the restrictions of your garage door sensors? If so, then this post is here to help! With a few simple tricks, you’ll be able to trick the sensors so that your vehicle can pass through the garage without being detected.
You might think it’s impossible, but with just a little bit of flair and imagination we promise it’s achievable. So get ready to surprise both yourself and anyone else watching – here’s how to trick garage door sensors!
Understand How the Sensors Work
Knowing how the garage door sensors work is essential to tricking them. All modern garage doors have two sensors that are mounted on either side of the door near the ground, which detect the presence of an object or person beneath it. When a person or object is detected, it sends a signal to the control panel that opens and closes the door.
In order to bypass the sensors, it’s important to first understand how they work. The sensors create an invisible beam of light across the garage that is known as the “safety line.” If this safety line is broken by a person or object, then the sensor will trigger and send a signal to open or close the door.
The most common way to trick these sensors is to use something to block the safety line between the two sensors. This can be done by using an object such as a chair or blanket to cover up the beam of light and prevent it from connecting with the other sensor. Once this has been done, you should be able to open or close the garage door without triggering the sensors.
10 Steps How to Trick Garage Door Sensors
Locate the Sensors
The first step in tricking your garage door sensors is to locate them. Most garage doors have two sensors, one on either side of the door. The sensors are usually located about 6 inches above the ground and should be easy to spot if you look closely.
Check for Obstructions
Once you have located the sensors, check for any obstructions that may be blocking their view of each other. This could include leaves, weeds, or even dirt buildup. If there is an obstruction, then it needs to be cleared away before you can proceed with tricking the sensors.
Cover One Sensor With Tape
Once you have ensured that there are no obstructions blocking the view of the sensors, cover one sensor with a piece of tape or cloth so that it cannot see its partner sensor. This will make it appear as though there is something blocking the path between them and will cause the garage door to think that something is in its way and not open properly.
Place an Object Between Both Sensors
Now place an object such as a broom handle or a stick between both sensors so that they can still “see” each other but cannot detect any actual movement in front of them. This will cause the garage door to think that something is in its way and not open properly.
Adjust Sensitivity Settings
If your garage door has adjustable sensitivity settings, then adjust these settings so that they are more sensitive than usual. This will make it easier for you to trick the sensors into thinking something is in their way when nothing actually is present in front of them.
Use Magnets
Another method for tricking your garage door sensors involves using magnets placed directly on top of one sensor so that it cannot detect any movement from its partner sensor on the other side of the door frame. The magnet should be strong enough to block out any movement from its partner sensor but not too strong, as this could damage or break either one of them permanently.
Use Aluminum Foil
You can also use aluminum foil to trick your garage door sensors by placing it over one sensor so that it cannot “see” its partner sensor on the other side of the door frame anymore and thus thinks something is in its way when nothing actually is present in front of them anymore. This means that the door will not close even if it has been triggered by a motion sensor or remote control.
Another option to use aluminum foil is to substitute one of the photoelectric sensors with a piece of foil. The foil needs to be wrapped around an object like a cardboard tube and placed in between your garage door and its frame for this method to work.
Move One Sensor Slightly Out Of Alignment
If all else fails, then try moving one sensor slightly out of alignment with its partner on the other side of the door frame so that they no longer line up perfectly with each other and thus cannot detect any movement from each other anymore, which will cause your garage door to think something is in its way when nothing actually is present in front of them anymore.
Test Your Trick
Once you have completed all the steps above, test your trick by pressing your remote control button or manually pressing down on your wall switch and seeing if your garage door opens or closes properly. If everything works correctly, then congratulations! You have successfully tricked your garage door sensors!
However, if any of the steps failed to work and your garage door still isn’t opening or closing correctly, then double-check all your connections. Make sure that you have wired each wire to the correct terminal and connected them securely. If everything looks good, then it’s possible you may need to reprogram your circuit board in order for your trick to work properly.
Troubleshoot Any Problems
If, however, things don’t seem to work correctly after trying all the steps above, then don’t worry – simply troubleshoot any problems by checking all steps again and making sure everything has been done correctly before proceeding further.
A great place to check for a reliable solution is online forums, where you can ask an expert or another user for advice on the issue you are experiencing. You can also refer to your garage door’s instruction manual if it has one, as this guide may provide additional information and troubleshooting tips you might find useful.
Things to Consider When Tricking Garage Door Sensors
When it comes to tricking garage door sensors, there are a few key things to consider. First, you’ll want to make sure that the tricks you use won’t damage your garage door system in any way. It’s important to keep safety at the forefront of your mind when attempting any type of garage door hack.
In addition, if the security system of the garage door is linked to an alarm system, it’s important to consider how the trick will affect that before you proceed. If there are any security measures in place, make sure you know what they are and how the tricks may impact them.
Finally, it’s also important to think about potential consequences if your attempt at tricking garage door sensors fails or is detected by the system. For instance, if you are tampering with a garage door that is part of an alarm system, it could trigger a false alarm or security breach which can come with hefty fines.
Some Common Mistakes To Avoid When Tricking Garage Door Sensor
If you’re attempting to trick a garage door sensor, there are some common mistakes that you should avoid at all costs. Overriding the safety feature built into the sensor can be dangerous and can result in serious injury if not done properly. Here are some of the most common mistakes people make when trying to override a garage door sensor:
- Not Testing the Door Sensor First – Before attempting to override the sensor, it’s important that you first test the door itself to make sure it is functioning properly.
- Not Checking if Access is Prohibited by Law – Even if the door sensor is faulty or disabled, it’s important to check with local laws and regulations to see if overriding the safety feature in a garage door is legal.
- Not Understanding the Mechanism Behind the Door Sensor – In order to successfully override a garage door sensor, you must have an understanding of how it works.
- Using Unsafe Materials – When attempting to override the door’s safety sensor, it’s important to use materials that are up to code and safe for the environment.
Conclusion
Hopefully, this blog post has provided you with a better understanding of how garage door sensors work and how to trick them. With these tips, you will be able to keep your home secure while opening your garage door quickly and confidently. If you ever have any questions about tracking your garage door, contact the team at ABC Garage Doors and we’ll be happy to help.
Our team is full of experts on all kinds of garage door issues, so you can rest assured that your problem will be quickly solved. Don’t wait around for a broken garage door sensor to render your home vulnerable. Take control of the situation today – use our tips on how to trick garage door sensors now!
